Match the complete tool model to the controller nameplate, suffix and approved cable. This comparison separates reviewed published pairings, local-table-only evidence and unresolved source conflicts; it does not certify universal interchangeability.
| Tool series and model inquiry | Controller page | Evidence and conditions |
|---|---|---|
| SNT-CS / SNT-CSM SNT-CSM103/106/110 SNT-CS301/302F/303 SNT-CS503/505/507 SNT-CSM712/SNT-CSM718 SNT-CSM725 SNT-CSM940/SNT-CSM960 | KL-NTCS-M7 | Reviewed tool/controller pairing. CSM103/106/110 ranges are kgf·cm; do not relabel them N·m. |
| SGT-CS SGT-CS301/302F/303/503/505/507/712/718/725 | KL-GTCS | Pairing supported by headquarters and reviewed Thailand rows. Legacy 3sigma/AVG.,5% is not an approved ±5% accuracy guarantee. |
| SGT-CC612/620/650/670 SGT-CC612/620/650/670 | KL-TCC | Reviewed Thailand pairing; CC620 is not CC625. Do not substitute GTCS or NTCS. |
| SKT-CGS10/24F/30 SKT-CGS10/SKT-CGS24F/SKT-CGS30 | KL-TCG | Reviewed local tool and controller rows; confirm the exact tool bit and matching cable. |
| SKT-CG30/50/70 SKT-CG30/SKT-CG50/SKT-CG70 | KL-TCG | Reviewed local matching rows. CG70 bit codes are not identical to CG30/50. |
| SKT-LCG30/50/70 SKT-LCG30/50/70 | KL-TCG | Reviewed tool rows list KL-TCG, not KL-TCG-L. Do not infer a controller suffix from LCG. |
| SKT-CG120/180/250 SKT-CG120/SKT-CG180 SKT-CG250 | KL-TCG-L | Reviewed local matching rows distinguish the -L controller; verify nameplate and revision. |
| SKT-EPT310/330 DC SKT-EPT310/330 DC | KL-EPTC | Published tool/controller mapping agrees for these named models. Pinout and PLC/MES readiness still require confirmation. |
| SKT-EPT530/550/570 DC SKT-EPT530/550/570 DC | KL-EPTC / KS-TM-EPTC | SOURCE CONFLICT: incorrect legacy CG specification rows withdrawn. KL-EPTC mapping omits EPT550; body uses KS-TM-EPTC. Numeric torque/speed/accuracy and complete configuration await manufacturer confirmation. |
| SKT-LEPT530/550/570 DC SKT-LEPT530/550/570 DC | KL-TCG (local tool table) | LOCAL TABLE ONLY: exact headquarters LEPT manual and approved mapping not independently verified. Do not copy LCG or EPT compatibility. |
| SKT-EPT7120/7180/7250 DC SKT-EPT7120/7180/7250 DC | KL-EPTC-L / KS-TM-EPTC / KL-EPTC | SOURCE CONFLICT: tool table -L, body KS-TM-EPTC and unsuffixed controller map differ. Keep this DC-title listing separate. |
| SKT-EPT7120/7180/7250 (no DC in title) SKT-EPT7120/7180/7250 | KL-EPTC-L / KS-TM-EPTC / KL-EPTC | SOURCE CONFLICT: published rows are also DC40V; the title does not prove AC. Matching numbers do not prove an identical variant. Keep separate quotation origin and URL. |
Configuration questions
Is a published pairing a complete installation approval?
No. It identifies the evidence reviewed for the named model. Confirm controller revision/firmware, electrical supply, matching cable/connector pinout, holder/bit, start/reset/interlock signals, accessories and included items before installation.
Does counting or a turns value prove actual torque and angle records?
No. Count, measured torque, calibrated angle and traceability are separate acceptance items. Confirm sensor versus tool accuracy, joint conditions, calibration, OK/NG logic, workpiece ID, record fields, export and retention. A port name alone does not prove PLC/MES integration.
Can EPT7 pages be merged because their numbers match?
No. Keep DC-title and non-DC-title pages, canonical URLs and inquiry origins separate until reliable manufacturer evidence resolves the relationship. Both current rows say DC40V. Resolve KL-EPTC-L, KS-TM-EPTC and KL-EPTC labels using the actual nameplate and approved manual.
What is required for a specific-model quotation?
Open the named tool page, choose the complete model and use its existing inquiry button. State quantity, target torque and unit, screw/joint, controller nameplate including suffix, cable/bit, required signals and records, site supply, company/contact, delivery location and required receiving date. Price, stock and lead time require sales confirmation; a listed product is not a stock promise.
Sensor Systems · Counting, torque and angle records · Workstation selection
